Call Today

 

This post listed below about Installing A Bathtub is absolutely fascinating. Don't miss out on it.

Mounting a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old tub is easily available, the project can move quickly; if you have to open a wall surface to remove the old bathtub as well as position the new tub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to leave the old tub and embeded in the brand-new one. Ensure you have actually certified on your own for the work and fit trying it. Rather than employing a specialist to take control of a halfway-completed job, it is better to take into consideration employing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly aid you set up a new bath tub in your bathroom if you have actually already gotten a brand-new tub as well as do not require to transform the setup of your previous water pipes.
Your tools and material list should make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Getting ready for the Setup

Firstly, the sustaining structure provided with the bath needs to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing taps can be quite problematic because of the restricted accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Using the two wood boards under its feet, put the bathtub in the required placement. The wood boards are helpful in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be attained by examining the level and also changing the feet on the bathtub up until the level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Turn on the water and also inspect all joints and also new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub needs to wait till the bathtub has actually been utilized at least once as this will resolve it into its final placement.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Tub

In the area where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall in between the bath as well as the tiling, bring about issues with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to permit the activity experienced when the tub is in usage. The sealer can split fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our piece on Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to browse our blog. Enjoyed reading our review? Please share it. Help another person discover it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .

Get Estimate